Northern Design Rail 350 Meters via Octopus Gateway
Book a Demo

Wattics customersDiscover how we can help you drive savings & increase sustainability for your customers or organization

Wattics companyLearn more about who we are, our core values and why our customers choose to partner with us


Northern Design Rail 350 Meters via Octopus Gateway

DISCLAIMER: The Octopus Gateway is no longer available through Wattics – please contact our support team ([email protected]) about connecting your Northern Rail Design 350 meters to the Wattics energy management platform through another gateway device (Carlo Gavazzi, Schneider, Accuenergy and more) available though Wattics.


Are you ready for energy savings? Enable our cloud-based energy analytics and energy dashboard for your Northern Design Rail 350 meters, to discover, measure and verify savings in the premises you manage.

The Northern Design Rail 350 is a multi-function meter measuring kWh, kVARh, kW, V, A, PF & Hz. You can now connect your Rail 350 meters to Wattics via our Octopus gateway in a few steps.


It is assumed that your Rail 350 is already wired and collecting measurements. If not, read and understand Northern Design manuals for installing, operating, or maintaining your Rail 350 meter. Installation and program procedures must be carried out and inspected by qualified personnel. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with this product.


1 RS485 connection



Make sure that all devices are powered off before any wiring is done.


If you have received a RS485 cable with your Octopus, you must connect it to the meter (or first meter of the daisy chain) as follows:

Yellow wire = input 15
Blue wire = input 16
Red wire = input 17


If you are building your own RS485 cable, please follow the colour code and sequence below.


Cut/isolate the other wires before powering up the Octopus to avoid unexpected shorts. You can then click the RS485 cable to the Octopus RJ12 connector.


Switch on the resistor if you have a daisy chain installations.


2 Meter Modbus setting

You must check and write down your meters’ Modbus address and baud rate via their display. You will need this information when configuring the Octopus.


3 Octopus Software Configuration


3.1 Download the Octopus Software Tool (Windows)




    3.2 Connect your Octopus to your computer

    Connect your computer running the Octopus Software Tool to the same network as the Octopus.



    3.3 Configure your deployment setup

    Launch the WatticsTool.exe Software Tool and create a new Branch, using the “+” button. Fill the “Branch Name” field with a short name for your project, and insert the serial number of your Octopus Gateway that you can find on its sticker or on its box.


    Select the correct timezone in the Timezone dropdown menu. If you cannot find your city select the closest city to your site location which is in the same timezone.


    Click on Network Configuration to enable Internet access for your Octopus. You can enable DHCP to get the Octopus to connect to the Internet automatically (Tick DHCP, click on Discover, and click on Set when the Octopus IP address is shown). For LAN access with manually assigned static IP addresses, you will need to get network parameters from your IT department and enter them here.


    If you use a GPRS sim card for Internet access, you must enter your APN name and APN credentials here.


    You must now set up the Wattics URL where data collected will be sent to. Click on Services button, and set the following:

    • Enable Service 1
    • Set Wattics as Service Name
    • Enter as Service Host Address (IMPORTANT: When using GPRS Sim cards or when your firewall does not support the use of URLs, you must enter as Service Host Address.)
    • Set 4401 as Port
    • Click OK.

    You must click OK to create the Branch.


    Once back to the Octopus Software Tool landing page, you can select your Branch and click the “Add” button on the right side to register the Northern Design Rail 350 meters connected to the Octopus.


    Find your meter in the drop-down menu and click Add.


    At the next screen, you must enter the meter name, its Modbus address, baud rate, and whether it is connected to the Octopus Gateway via RS485 or via the LAN (RTU485 or LAN).


    The device name must be a unique name identifier. Unless a convention has been pre-agreed with us, we ask you to use the following naming convention for choosing your unique name identifiers:


    OctopusID-counter nameofdevice


    (for example use 230007E7-1 Plantroom for the Plantroom meter if this is the first device configured via the Octopus Gateway ID 230007E7 and if Plantroom is the name you want to see in the dashboard for that meter. The next device will use the -2 counter extension etc)

    Make sure to insert a space between OctopusID-counter and nameofdevice
    For RS485 connections, you must set the same serial line settings registered within your meter and click OK.

    IMPORTANT: Set the response time to 500 if using multi-channel meters or daisy chain configuration, to allow all the Modbus devices to return measurement in time.

    For LAN connections, you must enter your Modbus device’s IP address and click OK.

    The next screen shows you all the parameters available for that Modbus device. You may unselect some parameters if you are not interested in all measurements. Click OK to save your configuration.


    The Modbus device now appears in the list of devices registered within your branch.


    You can now add more meters if you have a daisy chain.


    Once you have all your devices created, you must deploy your configuration onto the Octopus Gateway. Select your branch and click on the Deploy button.

    On the pop up window, leave the default settings and click on Deploy.


    Your Octopus Gateway is now configured for data collection from all the devices connected. We recommend that you save your project should you need to modify the configuration as a later stage. You will then be able to update an existing project when you add new meters.


    4 – Check that the Octopus is collecting data from the meter(s)


    Launch the CDT.exe Software Tool, enter your Octopus serial number and click on Connect.


    Once connected, click on the Real-Time tab, and verify that you are getting new event logs for the various electrical parameters every few seconds. This confirms that the Octopus is getting the readings from the meter via Modbus. You can then close the CDT tool. Verify your project file settings if you don’t see any data coming in.


    5 – Submit your Octopus project to Wattics




      Wattics will use your project file to double check that the setup is correct and that data is being received from your Octopus Gateway unit and correctly showing in your dashboard. You will then receive access to your Wattics dashboard, and from then on you will be able to log in to your Wattics Dashboard at and get started!


      Most Popular

      eGauge via HTTP

      SolarEdge API

      Itron Gas Volume Converter CORUS (PTZ) via Octopus Gateway

      Schneider Com’X 510 via FTP

      Rainforest Eagle Gateway via HTTPS

      via Octopus Gateway

      Klik 22 Electrical Meters via Octopus Gateway

      Omron KM-N1-FLK via Octopus Gateway

      Northern Design Rail 350 Meters via Octopus Gateway

      Carlo Gavazzi EM21 via Octopus Gateway

      Landis Gyr ULTRAHEAT T550 (UC50) via Octopus Gateway

      Schneider TAC Xenta 411 via Octopus Gateway

      Itron Gas Volume Converter CORUS (PTZ) via Octopus Gateway

      Create your own integration

      Not supported yet? Don’t be left behind and integrate now

      Go to the page

      Energy & Air Analytics Dashboard

      Learn more about the analytics tools in the Wattics platform to analyse energy and air quality performance in your facilities

      Check features

      Subscribe to our blog

      Sign up to keep up-to-date with what’s happening within the industry