Eaton PXM 2000 Meters via Octopus Gateway
DISCLAIMER: The Octopus Gateway is no longer available through Wattics – please contact our support team ([email protected]) about connecting your Eaton PXM meters meter to the Wattics energy management platform through another gateway device (Carlo Gavazzi, Schneider, Accuenergy and more) available though Wattics.
Are you ready for energy savings? Enable our cloud-based energy analytics and energy monitoring dashboard for your Eaton PXM meters, to discover, measure and verify savings in the premises you manage.
The PXM 2000 offers comprehensive world-class power and energy measurement and monitoring that reduce day-to-day operating costs and help avoid costly business interruptions. You can now connect your PXM 2000 meters to Wattics via our Octopus gateway in a few steps.
It is assumed that your PXM 2000 is already wired and collecting measurements. If not, read and understand Eaton manuals for installing, operating, or maintaining your PXM 2000 meter. Installation and program procedures must be carried out and inspected by qualified personnel. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with this product.
1 RS485 connection
Make sure that all devices are powered off before any wiring is done.
If you have received a RS485 cable with your Octopus, you must connect it to the meter (or first meter of the daisy chain) as follows:
Yellow wire = + input
Blue wire = – input
Red wire = SH input
If you are building your own RS485 cable, please follow the colour code and sequence below.
Cut/isolate the other wires before powering up the Octopus to avoid unexpected shorts. You can then click the RS485 cable to the Octopus RJ12 connector.
Switch on the resistor if you have a daisy chain installations.
2 Meter Modbus setting
You must check your meters’ Modbus address and baud rate via their display. You will need this information when configuring the Octopus.
If you don’t know how to find those, go to Page 55 (6-9) of the Eaton PXM 2000 user manual.
3 Octopus Software Configuration
3.1 Download the Octopus Software Tool (Windows)
3.2 Connect your Octopus to your computer
Connect your computer running the Octopus Software Tool to the same network as the Octopus.
3.3 Configure your deployment setup
Launch the WatticsTool.exe Software Tool and create a new Branch, using the “+” button. Fill the “Branch Name” field with a short name for your project, and insert the serial number of your Octopus Gateway that you can find on its sticker or on its box.
Select the correct timezone in the Timezone dropdown menu. If you cannot find your city select the closest city to your site location which is in the same timezone.
Click on Network Configuration to enable Internet access for your Octopus. You can enable DHCP to get the Octopus to connect to the Internet automatically (Tick DHCP, click on Discover, and click on Set when the Octopus IP address is shown). For LAN access with manually assigned static IP addresses, you will need to get network parameters from your IT department and enter them here.
If you use a GPRS sim card for Internet access, you must enter your APN name and APN credentials here.
You must now set up the Wattics URL where data collected will be sent to. Click on Services button, and set the following:
- Enable Service 1
- Set Wattics as Service Name
- Enter octopus.wattics.com as Service Host Address (
IMPORTANT:When using GPRS Sim cards or when your firewall does not support the use of URLs, you must enter 18.104.22.168 as Service Host Address.)
- Set 4401 as Port
- Click OK.
You must click OK to create the Branch.
Once back to the Octopus Software Tool landing page, you can select your Branch and click the “Add” button on the right side to register the Eaton PXM 2000 meters connected to the Octopus.
Find your meter in the drop-down menu and click Add.
At the next screen, you must enter the meter name, its Modbus address, baud rate, and whether it is connected to the Octopus Gateway via RS485 or via the LAN (RTU485 or LAN).
The device name must be a unique name identifier. Unless a convention has been pre-agreed with us, we ask you to use the following naming convention for choosing your unique name identifiers:
Make sure to insert a space between OctopusID-counter and nameofdevice
IMPORTANT: Set the response time to 500 if using multi-channel meters or daisy chain configuration, to allow all the Modbus devices to return measurement in time.
For LAN connections, you must enter your Modbus device’s IP address and click OK.
The next screen shows you all the parameters available for that Modbus device. You may unselect some parameters if you are not interested in all measurements. Click OK to save your configuration.
The Modbus device now appears in the list of devices registered within your branch.
You can now add more meters if you have a daisy chain.
Once you have all your devices created, you must deploy your configuration onto the Octopus Gateway. Select your branch and click on the Deploy button.
On the pop up window, leave the default settings and click on Deploy.
Your Octopus Gateway is now configured for data collection from all the devices connected. We recommend that you save your project should you need to modify the configuration as a later stage. You will then be able to update an existing project when you add new meters.
4 – Check that the Octopus is collecting data from the meter(s)
Launch the CDT.exe Software Tool, enter your Octopus serial number and click on Connect.
Once connected, click on the Real-Time tab, and verify that you are getting new event logs for the various electrical parameters every few seconds. This confirms that the Octopus is getting the readings from the meter via Modbus. You can then close the CDT tool. Verify your project file settings if you don’t see any data coming in.
5 – Submit your Octopus project to Wattics
Wattics will use your project file to double check that the setup is correct and that data is being received from your Octopus Gateway unit and correctly showing in your dashboard. You will then receive access to your Wattics dashboard, and from then on you will be able to log in to your Wattics Dashboard at https://dash.wattics.com and get started!
Itron Gas Volume Converter CORUS (PTZ) via Octopus Gateway
Create your own integration
Not supported yet? Don’t be left behind and integrate nowGo to the page
Subscribe to our blog
Sign up to keep up-to-date with what’s happening within the industrySubscribe